Titanium Bar
titanium rod TA1-TA4, TA8-TA10, TA15-TA18, Gr1~Gr5, Gr7, Gr9, Gr11, Gr12, TI-6AL-4V Eli, Ti-6Al-7Nb Standard:? ASTM B348, ASME SB348, ASTMF67, ASTMF136, ISO-5832-2, ISO-5832-3, AMS4928, MIL-T-9047, JIS, GB/T2965-2007, GB/T13810-2007
titanium rod TA1-TA4, TA8-TA10, TA15-TA18, Gr1~Gr5, Gr7, Gr9, Gr11, Gr12, TI-6AL-4V Eli, Ti-6Al-7Nb Standard:? ASTM B348, ASME SB348, ASTMF67, ASTMF136, ISO-5832-2, ISO-5832-3, AMS4928, MIL-T-9047, JIS, GB/T2965-2007, GB/T13810-2007
Titanium Rod , Titanium Rod Gr4 , Titanium rod Ti6Al4VEli
Titanium is an ideal structural material. Titanium has a low density of only 4.5g/m3, which is 43% lighter than steel. However, titanium is twice as strong as iron and almost five times higher than pure aluminum. With low density and high strength properties. This combination of high strength and low density makes the titanium rod a very important part of the technology. At the same time, the corrosion resistance of titanium alloy rods is almost or exceeds that of stainless steel, so it has been widely used in petroleum, chemical, pesticide, dye, paper, light industry, aviation, space development, marine engineering and so on.
|
N |
C |
H |
Fe |
O |
Al |
V |
Pa |
Mo |
Ni |
Ti |
Gr 1 |
0.03 |
0.08 |
0.015 |
0.20 |
0.18 |
/ |
/ |
/ |
/ |
/ |
bal |
Gr 2 |
0.03 |
0.08 |
0.015 |
0.30 |
0.25 |
/ |
/ |
/ |
/ |
/ |
bal |
Gr 3 |
0.05 |
0.08 |
0.015 |
0.30 |
0.35 |
/ |
/ |
/ |
/ |
/ |
bal |
Gr 4 |
0.05 |
0.08 |
0.015 |
0.50 |
0.40 |
/ |
/ |
/ |
/ |
/ |
bal |
Gr 5 |
0.05 |
0.08 |
0.015 |
0.40 |
0.20 |
5.5~6.75 |
3.5~4.5 |
/ |
/ |
/ |
bal |
Gr 7 |
0.03 |
0.08 |
0.015 |
0.30 |
0.25 |
/ |
/ |
0.12~0.25 |
/ |
/ |
bal |
Gr 9 |
0.03 |
0.08 |
0.015 |
0.25 |
0.15 |
2.5~3.5 |
2.0~3.0 |
/ |
/ |
/ |
bal |
Gr12 |
0.03 |
0.08 |
0.015 |
0.30 |
0.25 |
/ |
/ |
/ |
0.2~0.4 |
0.6~0.9 |
bal |
Diameter or Thickness |
Allowable Deviation |
||
Hot forged rod |
Hot roll rod |
Cold rolled rod |
|
>7~15 |
±1.0 |
+0.6, -0.5 |
±0.3 |
>15~25 |
±1.2 |
+0.7, -0.5 |
±0.4 |
>25~40 |
±1.5 |
+1.0, -0.5 |
±0.5 |
>40~60 |
±2.0 |
+1.2, -0.8 |
±0.6 |
>60~90 |
±2.5 |
+1.5, -1.0 |
±0.8 |
>90~120 |
±3.0 |
+2.0, -1.0 |
±1.0 |
>120~160 |
±4.0 |
—— |
±1.5 |
>160~200 |
±5.0 |
—— |
±1.8 |
>200~230 |
±6.0 |
—— |
±2.0 |
Deviation of length(mm): L<500, +5max; L>500, +10max |
Processing method |
Diameter or Thickness (mm) |
Degree of Curvature (mm/m) |
Hot processing |
< 35 |
6 |
Hot processing |
≥35 |
10 |
Hot processed, polished & cold processed round, square rod |
< 35 |
4 |
≥35 |
5 |